Microscan HS-2D Instrukcja Użytkownika Strona 156
- Strona / 172
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
A-38 HS-21/HS-41X Handheld Reader User’s Manual
Serial Commands
85 Trioptic Options 0
Binary Dip Switch
86 Motion Detection: Event 3
Valid Range: (see register 39)
Motion detection is enabled by setting
register C4 to 0xF0.
This register is reset to 0 (disabled)
when register C4 is changed away
from 0xF0.
When motion is detected, this event is
posted.
See register 39 for list of events.
Also see registers: 20E
87 Motion Sensitivity 5
Valid Range: 0 to FFFF (#65535) ms
Also see registers: 86, 20E
93 Suppress Beep On Decode 0
0: Beep indicating decode before
JavaScript processing
1: Call JavaScript without beeping to
indicate decode
Normally, the Reader beeps as soon as
decodes are read and processes them
via JavaScript if necessary after the
beep. To enable JavaScript to control
the beep feedback, change this setting
to 1; this will suppress the beep; the
JavaScript would typically beep if the
decode is valid or start another read
cycle if it isn’t.
This setting does not suppress beeps
for anything but a successful decode
event.
98 Decoder HD field (FOI0) X Offset 0
Valid Range: 0 to 639 pixels
Decoder uses the pixels after the specified
pixel offset in the HD field (FOI0).
Also see registers: 53, 54, 99
Bit Controls Value
0
Trioptic Decoding,
Normal Quiet Zones
0: Disabled
1: Enabled
1
Allow Short Quiet
Zones
0: Disabled
1: Enabled
2
No Quiet Zones
(requires firmware
version 3280+)
0: Disabled
1: Enabled
- HS-21/HS-41X Handheld Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- Introduction 5
- Highlighting 6
- About This Manual 6
- Statement of RoHS Compliance 8
- 1 Quick Start 9
- Check Required Hardware 10
- USB Interface 11
- RS-232 Interface 12
- Install ESP 13
- Select Model 14
- Click the Show 16
- Connect Symbol 16
- Configure the Reader 17
- Save Changes in ESP 18
- 2 Using ESP 19
- Application Mode 21
- Tree Controls 22
- Menu Toolbar 23
- New Model 24
- Preferences > General Tab 25
- Preferences > Terminal Tab 26
- Sizing Information 27
- Preferences > Advanced Tab 28
- Use Default Storage Location 29
- Document Memo 30
- Model Memo 30
- Connection Wizard 31
- Bar Code Dialog 32
- Send/Receive 33
- Default Current Menu Settings 34
- Default all ESP Settings 34
- Advanced Options 34
- 3 Basic Operations 35
- Practice Targeting 36
- Motion Detect Mode 37
- Dual Optics 38
- Dual Optics Examples 39
- Operational Feedback 40
- 4 Communications 41
- Communications by ESP 42
- Communications Overview 43
- Parity (RS-232) 46
- Data Bits (RS-232) 46
- Preamble 47
- Postamble 48
- Preamble and Postamble by ESP 49
- Keyboard Mapping 50
- Communications Mode 51
- Text Commands 52
- Text Commands by ESP 52
- USB Keyboard Rate 53
- Baud Rate 54
- Stop Bits 54
- Data Bits 54
- Text Command Timeout 55
- 5 Read Cycle 57
- Read Cycle by ESP 58
- External Trigger 59
- Default Continuous Event 60
- Maximum Decodes per Read 61
- Read Cycle Timeout 62
- Read Cycle 63
- Targeting Zone Tolerance 64
- Morphological Preprocessing 65
- Camera Settings 66
- 6 Symbologies 69
- Symbologies by ESP 70
- Data Matrix 71
- Symbologies 73
- Sample Aztec Symbol 73
- Code 39 74
- Code 128 75
- Sample BC412 Symbol 76
- Code 93 77
- Codabar 78
- Interleaved 2 of 5 79
- Pharmacode 82
- GS1 DataBar 84
- Sample PDF417 Symbol 85
- MicroPDF417 86
- Composite 87
- Symbology Identifier 88
- 7 I/O Parameters 89
- I/O Parameters by ESP 90
- No Read Notification 91
- Targeting 92
- Button Stay-Down Time 95
- Motion Detect Event 96
- Image Quality 97
- 8 Advanced Operations 99
- Continuous Read 100
- Mirroring 101
- Motion Detection 102
- Window of Interest 103
- Linear Mode 104
- Terminal 105
- Terminal View 106
- Editing a Macro 109
- Terminal Right-Click Menu 110
- Terminal Dropdown Menu 111
- 10 Utilities 113
- Device Control 114
- Differences from Default 115
- Firmware 116
- ID and Firmware Version 117
- Advanced 118
- Appendices 119
- General Specifications 120
- USB Cable Pinouts 123
- RS-232 Cable Pinouts 123
- Configuration Symbols 124
- Appendix D — Serial Commands 135
- Packetized Commands 136
- Command Types 138
- Simple Protocol 142
- Reader Settings 143
- Binary Dip Switch 144
- Field of Interest 144
- Reader Settings Table 145
- Serial Commands 146
- CRB System 163
- Example CRC16 C Code 163
- Communications Protocol 166
- Appendix F — ASCII Table 167
- Appendix G — Maintenance 168
Powiązane produkty i podręczniki dla Czytniki kodów kreskowych Microscan HS-2D
(125 strony)
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji